Ross’ build thread in Minnesota

[ROSSDC]

First pic.jpg (64.16 KiB) Viewed 4292 times

My favorite car since 2005. It all happened very quickly I was in the habit of watching Great Cars on PBS when in May 2005 the episode on the Meyers Manx aired and it was all over, I was hooked. A few months of searching went by and I found what looked like a Manx II that I purchase November 23 2005.

Every year it gets some kind of modification typically over the long Minnesota winter and driver as much as possible over the short summer. I lover the car because if I want to change something or try something I can and do. It’s not my fastest, nicest, best handle or best of anything car but it feels like it is and gives me the biggest thrill to drive and build. My favorite Car.

It has had 3 transmissions and 5 engines and a ton of other mods. These are some of the modifications I've done over the years.

November 23 2005 my sun and I drove it home. It looked better than it was the tunnel was broke in half and held together with (not exaggerating) 3/16 thick steel floor boards, a couple bolt and about 5 gallons of silicone rubber. It had been painted more times than a person could count and holes cut all over in undesirable place. First step was a complete tear down.

Holes.JPG (44.91 KiB) Viewed 4292 times

DSC00095.JPG (57.28 KiB) Viewed 4292 times

[ROSSDC]

Patched the holes, moved the rear tubs up for shock clearance.

Glass-400.jpg (34.35 KiB) Viewed 4291 times

Outer cage

outercage-400.jpg (61.56 KiB) Viewed 4291 times

Inner cage

innercage-400.jpg (58.42 KiB) Viewed 4291 times

[ROSSDC]

2" wider X 3" longer rear trailing arms.
Bus transmission. I started with a 3 rib that would pop out of 2nd gear, then a 5 rib that developed a noise and now a 6-rib (hopefully the last)

ARMS.jpg (32.16 KiB) Viewed 4290 times

Engines
1. 1600 dual port
2. 2.2 Subaru with factory computer (this is now in my Westy)
3. Subaru 2.5 with 2.2 heads
4. 2.2 Subaru with Megasquirt
5. 2.5 Subaru with Megasquirt (No more please)

EJ22-400.jpg (39.96 KiB) Viewed 4290 times

EJ22_rear.jpg (29.77 KiB) Viewed 4290 times

[ROSSDC]

Radiator
First version use the stock fan and radiator. I was never happy with this because the fan would run constantly when at 60mph. Core is too small and air flow is poor. Ground clearance is also compromised and doesn't look that good.

radiator bumper3.jpg (36.77 KiB) Viewed 4290 times

dune_buggy_2009_rear.jpg (62.98 KiB) Viewed 4290 times

I got this idea from the Manxter. It cools great and shortens up the rear end.

IMG_2052.JPG (59.08 KiB) Viewed 4290 times

[ROSSDC]

Reinforced spindles with Porsche 914 spindles

Spindle.jpg (26.42 KiB) Viewed 4290 times

Custom spacer to use 911 bearings and hubs.

IMG_1377.JPG (41.5 KiB) Viewed 4290 times

This is poor planning.
VW link pin
Porsche 914 spindles
Porsche 911 hubs and vented rotors
Spacers to widen the Porsche 914 calipers to fit on the 911 rotors

IMG_1383.JPG (49.77 KiB) Viewed 4290 times

[ROSSDC]

Rear brakes are CB Performance.

Brakeline.jpg (75.25 KiB) Viewed 4289 times

Bus axles and CV joints

IMG_1951.JPG (63.83 KiB) Viewed 4289 times

Front beam is 6" wider, adjustable, trailing arm shock relocation kit with rear Vanagon shocks.

IMG_2259.JPG (63.91 KiB) Viewed 4289 times

[ROSSDC]

Wheels are real one piece forged Porsche Fuchs 16x7

IMG_2050.JPG (67.75 KiB) Viewed 4288 times

Yakima roof rack bars

Yakima Mount.JPG (24.16 KiB) Viewed 4287 times

[ROSSDC]

Speedometer is from a bicycle.

Speed 005.jpg (35.53 KiB) Viewed 4287 times

Speedometer pickup is just a magnet mounted to the inner CV joint.

Speedopickup.jpg (42.38 KiB) Viewed 4287 times

[ROSSDC]

Aluminum fuel cell with Subaru pump mounted inside.

Tank top.jpg (38.24 KiB) Viewed 4287 times

Tank open end.jpg (38.01 KiB) Viewed 4287 times

[ROSSDC]

Aircraft sun visors, Ford bendy dome light and Honda motorcycle mirror.

buggy_2010 011.jpg (59.71 KiB) Viewed 4287 times

Ugly but Yes I have heat and window defrosters.

buggy_2010 009.jpg (69.54 KiB) Viewed 4287 times

buggy_2010 020.jpg (64.88 KiB) Viewed 4287 times

[ROSSDC]

Front window hinges

Folding Window2.jpg (21.5 KiB) Viewed 4277 times

Wiper motor support was bonded to the bottom side of the hood. Very solid.

DSC00011.JPG (58.68 KiB) Viewed 4276 times

[ROSSDC]

DSC00079.JPG (49.3 KiB) Viewed 4276 times

DSC022.JPG (64.19 KiB) Viewed 4276 times

dune_buggy_2009.jpg (66.17 KiB) Viewed 4276 times

[joescoolcustoms]

Cool build!

I like that tube chassis. Did you do the chassis and cage yourself?

[ROSSDC]

I did build it. I started with the original roll bar that I think is 2" and used the Trick-Tools tube bender and made the rest from 1-3/4 x .083 wall. I use 2x2 around the base to lift the body 2 inches.

Bender.jpg (45.85 KiB) Viewed 4269 times

DSC00067.JPG (63.14 KiB) Viewed 4269 times

[manxvair]

Nice looking set up.